A LOT OF PROGRAMMING IN A SMALL PACKAGE
Novak has packed the Havoc Pro Brushless ESC full of programmability into one easy-to-adjust profile. The Havoc Pro includes a customizable Throttle Curve, which smoothes out throttle operation. In addition, the Havoc Pro’s Brake Frequency adjustment contains seven degrees of adjustability from a smooth and controllable brake to a more abrupt and grabbier feel. The dozens of adjustments allow drivers to fine-tune their vehicle’s throttle braking for better control and advanced handling.
But the customization doesn’t end with braking. Novak has also built into the ESC Li-Po Cut-Off Circuitry that prevents the batteries from going below the critical safety voltage level, and a Motor Rotation feature that allows the user to easily select the direction of the motor.
ADVANCED MOTOR TECHNOLOGY
To complete the affordable system, the sensored Ballistic motors contain an easy-to-adjust timing assembly that alters the RPM range and features interchangeable wound stator construction, which creates dozens of racing options. Additionally, these sleek motors are built to ROAR/IFMAR specifications, boast a removable shielded sensor harness, and contain a 12.3mm nickel-plated sintered Neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions. And like all Novak racing motors, these brushless motors are blisteringly fast, reaching speeds that will effortlessly satisfy any racer or basher.
HAVOC PRO/BALLISTIC BRUSHLESS SYSTEM FEATURES
- Sensor-based for excellent torque and low-speed driveability
- Oversized front bearing [1/2” x 3/16” (12.7 x 4.8mm)] for increased load handling and bearing life
- Rebuildable motor design with removable shielded sensor harness, rotor, sensor assembly, wound stator, bearing cap, hardware, sleeve and both end bells
- Nickel-plated, 12.3mm sintered Neodymium rotor with a 0.125” pinion shaft that accepts all existing pinion gears
- Nine adjustable parameters: Minimum Brake (10 settings from 3-50%), Drag Brake (10 settings from 3-50%), Dead Band (5 settings from 2-6%), Minimum Drive (5 settings from 2-12%), Throttle Curve (Linear, Expo-1 and Expo-2), Brake Frequency (7 settings from 1-8 kHz), Reverse, Motor Rotation and Li-Po Cut-Off
- Fifty percent more transistors than the Havoc 2S ESC for faster speeds, higher efficiency and increased load handling
- One-Touch Set-Up for quick, easy transmitter setup
- Locked Rotor Detection and Thermal Overload Protection (when used with a Novak sensored brushless motor)
- Novak’s Radio-Priority and Polar Drive Circuits
- Included 30x30x6mm ESC clear cooling fan (#5648) mounted on factory-installed heat sink
- Meets RoHS compliance and includes 120-Day Warranty
- Designed, assembled and tested by Novak in Irvine, Calif., using globally sourced components
HAVOC PRO/BALLISTIC BRUSHLESS SYSTEM SPECIFICATIONS
- Motor Size: 2.07” x 1.41” (52.6 x 35.8 mm)
- System Weight (w/o wires): 7.96 oz. (225.7 g)
- Input Voltage: 2S Li-Po cells or 4-6 NiMH cells (1.2V/cell)
- ESC Footprint: 1.16” x 1.49” (29.5 x 37.8mm)
- Motor Limit: All 3.5-turn Novak 540-size sensored brushless motors
- On-Resistance: 0.00040 ohms @ 25°
- BEC: 6.0 volts DC / 3.0 amps
- Rated Current: 540 Amps @ 25°C trans. temp.
- Braking Current: 540 Amps @ 25°C trans. temp.
- Status LEDs: 4
- Voltage Cut-Off: 6.25V
- Power Wires (battery/motor): 14G Super-Flex Copper-Strand Silicone Wire
- Sensor Harness: 9” (230mm)
- Watts: 195
- Kv (unloaded): 3,300 RPM/Volt
- Color-Coded Stator: orange
- Recommended Use: 13.5T spec-brushless racing
|
