Novak GTB 2 8.5T / 5000kV Traxxas Brushless System

This is a Novak GTB 2 8.5T / 5000kV Traxxas Brushless System. This brushless system is specifically for Traxxas customers. This is an affordable, "Plug & Play" combo ideal for racing in Traxxas vehicles. The new GTB 2 Brushless System is equipped with a high-current handling, Traxxas-compatible battery connector for easy, race-ready installation. In other words, no soldering! To simplify installation further, the system includes gold-plated bullet motor plugs, which eliminate tricky wiring and allow for easy plugging and unplugging.

The GTB 2 8.5T Traxxas Brushless System includes an 8.5T / 5000kV brushless motor - the fastest of the Novak SS Pro-Series brushless motors. It's a great choice for all-around bashing and speed runs. It is ROAR approved for use in Spec and Sportsman classes at drivers' local tracks. The SS Pro sensored motors have a nickel-plated sintered Neodymium rotor and Thermal Overload technology; they feature a shielded-sensor cable and a rebuildable design, allowing for replacement of various motor parts like rotors and bearings. This system is well-suited for 2WD applications, but will work in virtually all popular 2WD and 4WD Traxxas vehicles, including the Stampede, Slash, Rustler and Bandit.

Upgrading to Novak's brushless performance will give drivers a reliable, serviceable system with staying power for fast applications straight out of the box. Using the iTraxxas stock gear and batteries included with your Traxxas vehicle, the GTB 2 Brushless Traxxas Systems can provide a 20-40% speed and power increase, and all with easy, "Plug and Play" installation. All speed controls are backed by a 120-day warranty and Novak's leading customer service. Look no further, and put a Novak brushless system in your Traxxas today!

General Features:

• Multiple Adjustable Parameters Via On-Board Programming

• Plug and Play for Easy Installation and Setup

• Built-In Diagnostic Temperature Monitoring

• On-Board Hall Sensor Test

• NovaBrakes Provide Instantaneous Braking

• Sensor-Based for Excellent Torque and Low-Speed Driveability

• User-Friendly One-Touch Programming

• Robust 3 Amp BEC for Strong and Fast Steering Response Under Any Condition

• Water-Resistant Case with Silicone Gasket Seal

• Cross-Cut ESC Heat-Sink for Reduced Weight and Efficient Cooling

• Oversized Front Bearing for Increased Load Handling and Bearing Life

• Nickel-Plated 12.3mm Sintered Neodymium Rotor with 0.125" Pinion Shaft

• Pinion Shaft Accepts all Existing Pinion Gears

• Provides Approximately 20% Longer Run-Times compared to Brushed Motors

• Meets ROAR and IFMAR Specifications

• Meets RoHS Comliance and Includes 120 Day Warranty

Brushless ESC Specifications:

• Forward/Brake/Reverse

• Input Cells: 1~2S Li-Po/Li-Fe or 4~7 Ni-MH

• ESC Footprint: 1.16x1.47x0.97" (29.5x37.3x24.6mm)

• Weight w/o Wires: 1.29 Ounces (36.6g)

• On-Resistance: 0.00040 ohms @25ºC Trans. Temp

• Motor Limit: 540-Size 8.5T

• BEC: 6.0 Volts DC / 3.0 Amps

• Power Wire Size: 14G Super-Flex Copper-Strand Silicone Wire

• Status LEDs: 5

• Battery Plug: Traxxas (Installed)

• Motor Plug: Bullet (Installed)

Brushless Motor Specifications:

• Turns: 8.5T

• kV (Unloaded): 5,000 RPM/VOLT

• Watts: 280

• Maximum RPM: 50,000

• Motor Size: 2.08x1.41" (52.6x35.8mm)

• Motor Weight: 6.3 Ounces (180g)